Burst depth for the Sony A33 is seven Raw or Raw+JPEG frames, and 16 Fine or 20 Standard JPEG frames in a burst. That’s quite a bit less than the A55, which can capture twenty Raw or Raw+JPEG frames, while JPEG shooters can expect 35 Fine or 39 Standard-compression frames, but in our experience, the Sony A33 makes up for this deficit somewhat by clearing its buffer much faster. This means that although the A55 will get you more shots in a burst, the A33 will be ready to start another burst much sooner.
Heat is a result of the friction of electron flow. Half the current at double the voltage should result in roughly half the heat if using the same size wire. It’s why our grid transmits at 100k volt over long distances.
We use cookies to give you the best possible experience on our website. For more details including how to change your cookie settings, please read our Cookie Policy.
hmm, not sure why my comment went in the wrong place. looked like it was in the [ GuruBuckaroo] comment, when I pecked it in. The “unusual sensation” quip was spot on & funny!
ead of single layer traces covered by the paint, what about multilayer PCB? So the traces would be embedded between two FR4. This way it would be safer.
Lenovo is promising 30 percent better performance over its previous Miix 630 Windows on ARM device, and a surprising claim of 25 hours of battery life to match. While the battery life sounds impressive, it’s the performance that will matter in a device like this and we’ll need to test this latest range of ARM-powered laptops to see if app compatibility and performance has improved. Most Windows desktop apps will run emulated on these ARM-powered devices, but there are some limitations. As this is powered by the Snapdragon 850, there’s also built-in LTE support for mobile connectivity on the go.
*My* electricity is cheap (~$0.065/kW), so that 117 miles would cost about $7.61. Gas in my area is down to about $2.70/gallon, so the total fuel cost for those 253 miles would be about $16. Other areas of the country might be higher for electricity and lower for gas.
3-phase installations like industrial facilities and some apartments are fed with 208V 3-phase, which provide three phases of 120V to neutral, or 208V phase-to-phase.
I couldn’t even find a de-rating chart or graph online for this relay. Also, many SSRs (and other devices) do not recommend the “bottom” orientation for heat sinks.
Steady in the dark. The Sony A33′s Handheld Twilight (HHT) mode uses multiple shots and micro-alignment to permit handheld exposures even in very dark conditions. This was a very dark bar scene, but the shot came out sharp enough for a 5×7 print. It could have used some exposure adjust and (definitely) a different white balance setting. Exposure is auto-only in HHT mode, but the similar multi-frame NR mode gives full control.
BTW, one can’t just put in a big red button and call it Emergency Isolation Switch. At least in an industrial setting a Emergency Stop follows strict guidelines which include possible damage to the machine from using it. There are rules and regulations for how these are wired, where they are placed, etc. One doesn’t just run mains power through it. Typically these are low voltage switches that cut power to coils of high current contactors and relays.
Now that’s something … And for other commenters: of course exposed mains voltage is dangerous, lethal even. But why would it need to be exposed? It could be made like Davic’s hack, or in countless other ways that are safe. Hide heating element under thermal mass, use secure connectors and proper grounding.
Pioneer debuts three new wireless CarPlay systems | Circuit Breaker Parts Related Video:
We are also focusing on enhancing the things administration and QC program in order that we could keep fantastic advantage within the fiercely-competitive enterprise for Magnetic Contactor Supplier , Solid State Relay , Ev Charger , With the development and enlargement of mass clients abroad, now we have set up cooperative relationships with many major brands. We have our own factory and also have many reliable and well-cooperated factories in the field. Adhering to the "quality first, customer first, We are provideing high-quality, low-cost products and first-class service to customers. We sincerely hope to establish business relationship with customers from all over the world on the basis of quality, mutually benefit. We welcome OEM projects and designs.