While no standard is perfect, I have found that knowing the NEC and looking carefully at manufacturer listings and labels can save you time, your customers money, and help keep everyone safe.
No, it’s far more likely a combination of the strength of your flexor muscles (biceps) being stronger than your extensors (triceps), a bit of spinal reflex (sudden stretch of pain signal = withdraw limb) and observer bias; you’ve probably seen people electrocuted with 120v AC more often than 120v DC.
Personally, I would always design for the full rated power load of the outlet. Sure you will be aware of the limitations of the switch but not everyone reads the specs and you don’t want to blow up your switch when someone inadvertently plugs in a vacuum cleaner.
Well your musle will clench with AC as well. That’s why friend mine is still among the living. He was an oilfield pumper after n over night thunderstorm there was much equip down because of blown fuses and tripped motor over load protection devices my fried got an a hurry and got careless He reached int a motor control box and grab a fuse in each hand to pull them out. Because of other damage in the box they where energized. The jolt threw him on his ass because his hands clenched surround the fuses the act of throwing him back disconnect him from the electric power as the fuses pulled out out of their holders. I tech school one of the other student got bit by HV inside a TV and it threw his hand way. He wasn’t hurt by the electrical shock, but we kept an an eye him for a while because he looked like he could enter a state of physical shock.
By the way, the plug-in Kia Niro appears very similar to the now-discontinued plug-in Ford C-Max. I wish Kia better success with their product offering than Ford had with theirs.
Kapton tape is nice but I know it peels and needs replacing eventually. You wouldn’t legally be able to sell something using just tape as a mains insulator. Glass can break. It’s a small chance, but risk should be proportionate to the danger when things fail. You might sometimes have metal screws or whatnot on the bed if you’re assembling a couple of pieces there. Best not to mess.
So it’s – what happens to this board at 110 Volts and what are the consequences and the same for 240V, 1000V 10000V, ALL of these voltages. So it’s about what voltage will cause consequences and NOT what it is going to do at a specific assumed voltage, or more to the point ** where are the first points of failure with increasing voltage and what are the consequences.
These rules of thumb are referring to the amperage capacity or “ampacity” of the conductor (wire) and are often correct. Sometimes, these general rules lead technicians to believe that if an appliance is rated for 50-amp breaker/fuse maximum overcurrent circuit protector (MOCP), you must use 6-gauge wire and a 50-amp circuit breaker.
The list of absolutely required tools is missing the appliance tester. e.g. something like this http://www.fluke.com/fluke/m2en/Products/category.htm?Category=PAT or https://www.gossenmetrawatt.com/english/ugruppe/testingofelectrappliances.htm
In some cases, contractors have stated that certain municipalities are requiring that conductors be sized based on the breaker size instead of the MCA. This is not uncommon, but it is usually a matter of a respectful conversation about the above NEC articles. The “authority having jurisdiction” or AHJ is responsible for interpreting the code, and they can make any standard they see fit. While certain local legislation may supersede the NEC with additional regulations, the NEC is a nationally recognized standard throughout the U.S. It is rare that a building department will ignore entire articles of the NEC when it is brought to their attention in a respectful manner.
Tomczyk is a professor of HVACR at Ferris State University, Big Rapids, MI, and the author of Troubleshooting and Servicing Modern Air Conditioning & Refrigeration Systems, published by ESCO Press. To order, call 800-726-9696. Tomczyk can be reached at [email protected] (e-mail).
I’m a bit disappointed, I thought this was a safe place for dangerous ideas. If you want to diy an ELV heat bed go ahead, but that isn’t going to suit everyone.
Tom Baker is turning his long-lost Doctor Who movie script into a novel | Lrd12 Overload Relay Related Video:
We offer great strength in quality and development,merchandising,sales and marketing and operation for Ac Contactor Relay , Abb Contactor , La2 Relay Timer , More than 26 years, Professional companies from all over the world take us as their long-term and stable partners. We are keeping durable business relationship with more than 200 wholesalers in Japan, Korea, USA, UK, Germany, Canada, France, Italian, Poland, South Africa, Ghana, Nigeria etc.